1, well with the submersible pump material and application areas: submersible pump well casing is made of high quality stainless steel, to provide the most basic protection of equipment, its shaft, coupling, into the water seat and the pump Head, are new high-strength anti-wear composite polymer materials, and its impeller is also a stainless steel diversion shell, it is a new "floating" structure, well submersible pump impeller during operation without axial pressure on the motor . Such products are especially suitable for use in the fields of mining, agriculture, construction, and raising. Well used submersible pump structure diagram Interpretation (Asia Fluid Network) 2, the structural characteristics of submersible pumps with wells: 1) water outlet: the water flow into the location; 2) rubber bearings: between the shaft and the shaft for support; ) On the diversion shell: submersible pump per stage of the diversion shell with a rubber bearing; 4) impeller: impulse turbine rotor part, it is also a well with submersible pump work an important part; 5) rotor: 6) The stator: the stator core, the stator winding and the base of the three parts; well with submersible pump components also includes dowel bearing, thrust bearing, the bottom cover, the drain screw Plug, coupling, water plug, water festival and several other points. Because the use of submersible pumps wells is rather special, so well submersible pump components require relatively high demand, with the rapid development of science and technology in our country, and the market competitiveness of the market to increase, we pay more attention to such products Development, after years of development, wells with submersible pumps already have a very good foundation, the need is to continue its development and research. This article published by the Asian Fluid Network Editor, reprint, please indicate the Asian Fluid Network; Promotion Service Hotline:, QQ:; Related Articles: What are the characteristics of submersible pumps with well? Well with submersible pump profile
The coal carrier activated carbon has well-developed pore structure, good adsorption property, high mechanical strength, easy to repeat regeneration, low cost, and so on, it is used for purifying the poisonous gases, treating the waste gas, purifying the industrial and domestic water, and recovering the solvent.
Use: Used in the treatment of waste gases containing sulfureted hydrogen, methyl merecaptan, sulfur dioxide, methyl sulfide, dimethyl sulphide etc.
Spec.:
|
Model NO.
|
Moisture(%)
|
Strength(%)
|
Carbon tetrachloride(%)
|
Packing density(g/L)
|
Load content(%)
|
H2S(g/cc)
|
Grain diameter(mm)
|
| TZK-3070 |
≤15
|
≥95
|
≥70
|
≤660
|
KOH 6.0-8.0
|
≥0.140
|
Φ3.0
|
| TZK-4070 |
≤15
|
≥95
|
≥70
|
≤650
|
KOH 6.0-8.0
|
≥0.140
|
Φ4.0
|
| TZK-6070 |
≤15
|
≥95
|
≥70
|
≤630
|
KOH 6.0-8.0
|
≥0.140
|
Φ6.0
|
| TPK-4×8 |
≤15
|
≥95
|
≥60
|
≤580
|
KOH 5.0-7.0
|
≥0.140
|
3.6-3.8
|
| TPN-4×8 |
≤15
|
≥95
|
≥60
|
≤580
|
KOH 5.0-7.0
|
≥0.140
|
3.6-3.8
|
| TZI-4070 |
≤15
|
≥95
|
≥70
|
≤650
|
KI 2.0-6.0
|
≥0.140
|
Φ4.0
|
| TZS-4060 |
≤15
|
≥95
|
≥60
|
530-560
|
S 10.0-12.0
|
-
|
Φ4.0
|
| TPP-30×60 |
≤15
|
≥95
|
≥60
|
-
|
H3PO4 5.0-15.0
|
-
|
30×60 meshes
|
Coal Carrier Activated Carbon
Coal Carrier Activated Carbon,Coal Activated Carbon For Catalyst Carrier ,Coal Column Activated Carbon,Commercial Activated Carbon
SHIZUISHAN ZhongShi activated carbon co,.ltd , https://www.zscarbonchina.com