The bathtub is synonymous with comfort and warmth. It is quietly lying in the bathtub, surrounded by warm water, fading away from the fatigue, letting the tight nerves be released, and putting a soft music on it. But the headache is that the maintenance and cleaning of the bathtub is very troublesome. If the improper installation is done after the consumer buys it back, and if it is handled improperly, it is easy to cause the bathtub to crack. How can I make my bathtub more long-lived? Let us listen to the experts of Wrigley Sanitary Ware.
Most of the bathtubs use acrylic sheets, and high-quality acrylic sheets have the following advantages:
The acrylic bathtub is made up of a surface layer (acrylic layer) and an inner layer (glass fiber resin reinforcement layer). The inner layer of the good quality acrylic bathtub is tightly combined, without delamination, and gently tapping without a cavity sound, the surface Smooth as porcelain, flat as mirror, backlit, flat without undulations, polished lines, no warping on the straight surface, curved arc standard, uniform cylinder thickness, light weight, strong and elastic, hand-painted inside the cylinder It should be smooth, no powder, no hands, and the joint between the skirt and the cylinder is tight and the gap is consistent.
First, purchase
Tip 1, specific thickness. You can tap the bathtub to judge the thickness of the bathtub. The thickness of the bathtub is large and it will not crack naturally.
Tip 2, listen to the sound. Also pay attention to the size of the motor sound when buying a jacuzzi. Buy a high-end bathtub, it is best to "test the water" at the time of purchase, listen to the sound, try the temperature.
Tip 3, look at the gloss. Know the quality of the material by looking at the surface gloss, suitable for any kind of bathtub.
Tip 4, touch the smooth and smooth surface. It is suitable for steel plates and cast iron bathtubs, because both bathtubs need to be enamel-plated, and the plating process is not good, there will be fine ripples.
Tip 5, press the hand and press the foot to test the firmness. The firmness of the bathtub is related to the quality and thickness of the material. The visual inspection is invisible. You need to try it yourself, such as standing in, whether it feels sinking.
Tip 6. Choose a branded bathtub. In general, brand-name bathroom products, such as the bathtubs of the top ten sanitary brands, can make consumers feel more assured in terms of quality and after-sales service.
Second, the installation
The first step: test whether the water is leaking.
Before installing the bathtub, first install the water fittings, do the water shut for 24 hours, and see if there is any leakage in the bathtub. Pay special attention to the overflow. It is very difficult to close the water for 24 hours. On the outside of the bathroom, pour two buckets of water and try the water in the bathtub. This is convenient.
When it is actually installed, directly push the bathtub into the bathroom and put it in the water. Because the water level of the faucet left when changing the water is just the width of the bathtub. If the size of the bathtub and the water are not right, it is necessary. Note that the center point of the bathtub should be facing the center of the water mixing, otherwise it will be difficult to see after the mixer is installed.
After the bathtub is lifted into the bathroom, start to install the water and water accessories, fill the bathtub with water, close the water, check for water leakage, and when the water flows over the overflow, the water in the bathtub flows out from the overflow. At this time, I Just kneel on the floor, reach under the bathtub and touch the back of the overflow to see if water leaks from it. After the test of the overflow, the next step is to check the sealing of the water. I chose to stand still and observe the tightness of the water. There was no problem at the beginning. After about 10 minutes, the quiet bathroom was separated by a few seconds. The sound of bubbling in the water, the installation of the water was not sealed, there was leakage, and it was decided to let the water be reinstalled. This time I found the problem. The original copper pipe under the blisters, there was a sand hole in a certain part, and we were tossed several times and leaked. There is a bit of luck here. I put the bathtub into the bathroom from the beginning. When I put the water in the experiment, I am not afraid of water. It is also a full tank of water. Under the pressure, the sand hole is pressed, so it will leak. If it is only a small amount. The water, not so much pressure, will not leak at this time. If the skilled hydraulic worker is very impatient with my test, this problem may not be discovered at the time? On the other hand, it is proved from the side that the hardware that is sent is indeed of average quality, and the hardware is still to be bought.
It should be noted that the center point of the width of the bathtub is at the center of the faucet. This point must be thought of when the water is changed at the beginning. The width of the bathtub is 700. 750? 800? Once the water is changed to determine the size of the water, try to buy the bathtub according to this, otherwise It is very difficult to change the size of the mixed water from the wall.
The second step: the leveling of the bathtub.
When placing the bathtub, pay attention to the other end of the water outlet slightly higher than the end of the water outlet, so that the sewage will be poor in the future. This depends on the situation. The bathtub was originally suggested by Xiao Gong. It was observed that the bottom of the bathtub originally left the slope of the drainage. The level was used to level the four sides of the bathtub and then the water was tested. As expected, the water quickly drained. The bathtub maintains a visually beautiful appearance without affecting the drainage effect.
The third step: fill the sand.
Although the cast iron bathtub is strong, its thermal conductivity is very fast. It should be used in Zhonghesha, and it should be laid and tamped at the bottom of the bathtub. Bricklayers also recommend the use of foam. Considering that the foam is not as fluid as river sand, it is suitable to fill all voids. In the process of filling the river sand, how to make the sand not leak into the water pipe is a problem to be solved.
After all the placement work, the water release test is repeated (this step is mainly to ensure that the bathtub is not moved behind to make the water leak). After confirming the correctness, wait for the bricklayer to build the skirt.
The fourth step: check and repair.
Indoor Tract Lights,Clothing Store Spotlights,Indoor Rail Lights,Indoor LED Tract lights
Sichuan Kangruntengpu Photoelectric Technology Co., Ltd. , https://www.krtoplighting.com