Gear parts are important components of the reducer, and its quality directly affects the service life and safe production of the reducer.
After the emergence and use of gear processing machines, the bottleneck that seriously affects and restricts the quality of gear processing occurs in the blank forging process and heat treatment process, especially the heat treatment process.
(1) The forging process of the tooth blank is not strict because of the process, and internal cracks are prone to occur. It is not easy to be found and detected during the machining process, and often the workpiece is in the finished product or semi-finished product, and the internal cracking causes the waste to be generated under the action of internal stress. Quality accidents, such quality problems occur from time to time and should be strictly observed.
(2) Heat treatment process Gear parts are generally subjected to heat treatment twice or more. The main purpose of heat treatment of the tooth blank is to eliminate the internal stress caused by the hot forging blank, improve the metallographic structure and workability of the tooth blank before processing, thereby improving productivity, saving tool costs, improving machine tool utilization, reducing and preventing Deformation during machining or during heat treatment.
The purpose of heat treatment after tooth profile processing is to improve the hardness, working strength and wear resistance of the tooth working face. In this heat treatment process, the gear parts are easily deformed, and it is necessary to carefully operate, carefully explore the law, strictly control the heating time during quenching, the holding time, the size of the workpiece and the placement in the furnace, and minimize the workpiece in the process. The amount of deformation.
For cylindrical gears, if the amount of deformation is too large, in the process of finishing the tooth surface, there is a single-side tooth grinding that does not come out and waste occurs.
Or the tooth-tooth direction changes in the fine grinding, so that the contact area is biased to one side, affecting the position of the contact area, and failing to meet the requirements.
Bevel gears are required to be high during heat treatment, but are also deformed after heat. After the final heat treatment, the deformation of the gear shaft is the center deviation of the shaft body and the shaft head. The deformation of the gear is an overall bow change. During the hard tooth surface scraping process, a convex and concave surface appears. A few teeth on one side advance into the cutting and the other side is cut into the teeth. There is also black skin when thick, which does not meet the requirements, and the tooth surface is not completely cut. The carburized layer that has entered the cutting tooth surface in advance has been thinned and even cut off, so that the teeth lose hardness and strength, and the surface looks good, but the life is greatly reduced when actually used in boxing.
In short, in the production process of gear-type workpieces, from the forging of the tooth blank, to the heat treatment after roughing and the heat treatment after finishing, the process flow of each process must be strictly implemented to reduce waste, save costs and improve Product quality is very critical.
LEDER technology`s ceiling light takes fashion design, more stereoscopic than other flat ceiling lights. Ideal luminous output for indoor use,step-less dimming, white light, warm light, neutral light, three bright modes are available. Perfect for balcony, bar, cafe, clothing store, aisle, etc.
This flush mount edge-lit LED technology of the ceiling light channels the light to the side of the fixture and then redirects it downwards, creating a uniform light distribution without hot spots, flicker or glare.Station it in the dining room above a rectangular table to find just the right light at your next casual dinner gathering, or hang it up over the entryway to put a spotlight on the foyer as guests walk in.
Features:
• Fashion design
• Easy to install
• Incandescent, and CFL
• Energy saving electricity
• Product Type: Semi flush mount
• Color temperature :3000k-6000K
• Sloped ceiling compatible
• Type of protection: IP20 /IP65 (Some models)
• Warranty:3 - 5 years
LED ceiling lights are an especially good choice for anyone looking for a lamp which is elegant in an understated way. If you want a lamp that discreetly keeps itself out of the way, yet looks great once you actually pay attention to the ceiling light, you have definitely come to the right place. This ceiling light will do its job very well.
We have rich production experience in lighting. Except LED Ceiling Light, we also offered other product in Indoor Lighting .Such as : LED Downlight , LED Panel Light, Track Light , Linear Light , LED Strip Light , LED Tube Light , LED Bulb , as so on .
Bedroom Ceiling Lights,Bathroom Ceiling Lights,Home Depot Ceiling Lights,Semi Flush Ceiling Lights
JIANGMEN LEDERLIGHT LIGHTING Co.,LTD , https://www.walllightindoor.com