Tile inspection to see what?
Whether the packaging is complete and firm, specifications, color number, grade, code, production date, site, etc.; check whether the color number and size marked on the outer packaging are the ones they ordered;
Pay attention to whether the tiles are unified in batches, and the difference in size and color of different batches of bricks will be large;
Randomly check the tiles, the surface of the glaze is uniform, and the texture and pattern are the same. Whether there is color difference (even if the same color number can not rule out a slight chromatic aberration), missing corners, cracks and other defects. Pay attention to the brand, the internal brick and brick neatly arranged and a protective film to prevent cracking;
Pull out a piece of ceramic tile and place it on a flat countertop. The corners are not tilted. The two tiles meet on the back and the contact is tight and uniform.
Tile laying key points, owner supervision manual
Tiles are a face-saving project, and every time there are netizens who have finished their decoration, they are so sad and frustrated that the reason is only that - the tiles are ugly! The master craftsmanship can be varied over time, but the supervisors must be able to help the tiling project. With the supervision of the supervisor, each of the following points will gather the true experience of netizens and pay attention to taking notes!
First, waterproof yet? Waterproof treatment is first performed. Tiles can be laid after 24 hours of closed water test without leakage.
Second, did you not level it? You must level the ground first, or wet it together to level it. When the kitchen and bathroom are leveled, they should pay attention to the gradient of water flow and direct the water to the floor drain. Water does not accumulate, and water does not flow backwards; the thickness of cement mortar can be appropriately thinned when the bathroom floor tiles are used, making the bathroom floor slightly lower than other floors.
Third, is it clean? The cement label used for paving should be low-grade. Wall cracks must be treated before the tiles can be attached, before tiling should pay attention to the master to clean up the grass, if there are lime plaster on the wall, wallpaper, etc. must be cleaned, or after the cement mortar and grass roots are not easy to lose bricks.
Fourth, not soaked in water? Glazed tiles, especially wall tiles must be soaked in water before the paving, the specific time of immersion in the tile packing instructions shall prevail, are generally immersed in the brick body can not bubbling on it, and then picked up and dried again. If it is not immersed in water, the water in the cement layer will be rapidly absorbed and solidified by the dry tiles and the tiles will not stick. It is necessary to say that if your home is a vitrified tile, you do not need to soak, because the vitrified tile does not absorb water and soak. It doesn't matter much; the bubble bricks are also planned, and they can't be soaked too much at one time, because tiles that have been blistering cannot be returned.
Fifth, make it clear! Before paving, be sure to carefully explain the direction of laying the bricks to the worker who is responsible for the paving, that is, horizontally or vertically, where the flowers and the waist line (or parquet, different color bricks, etc.) are attached; buy antiques Brick classmates should pay more attention to it. The shopkeepers need to look at the paving design drawings and explain them in detail to ensure the paving effect. In the event of a mistake, they will regret it. Often, expensive embellishment tiles are laid out in corners.
Sixth, first stake out! Before formal paving, it is best to pre-shop, adjust the effect to the best condition, and then actual paving; when there are half bricks, it should be placed below.
Seventh, after the wall tiles are pressed, the floor tiles are pressed; the tiles are covered with tiles from the inside to the outside. Brick tile paving with stress, behind the brand logo or arrow points to the same, it is easier to flat and beautiful.
Eighth, pay attention to leave the seam! General tile paving seam left 2-5mm, even if it is seamless bricks have to set aside 1mm expansion joints to prevent deformation after thermal expansion and contraction tiles cracks.
Ninth, check emptying in 12 hours! After the tiles have been tiled, check the empty drums and use the rubber mallet to randomly hit the brick surface. Every place knocks on the sound. It's easy to hear the following if there is no hollowing out, and there are more knocks! If empty drums do not allow the re-attachment, if the cement is reconstituted and reworked more complicated, the tiles may be damaged and cannot be reused.
Tenth, again after 24 hours! After the floor tiles are laid, bricks must be covered with cardboard, etc., and they must be walked on the brick surface at least 24 hours before the jointing.
Construction Acceptance Ceramic Tiles Tiles Cement Decoration Kitchen Wall Tiles Antique Tiles Bathroom Tiles Bathroom Tiles Bathroom Size Bathroom Design Bathroom Design Toilet Waterproof Bathroom Tiles Kitchen Tile Tiles Specifications
Low carbon USS flat washers, typically used with Grade 8 or hardened steel bolting, are used under bolt heads or nuts to increase the bearing surface area, or to offer protection so that the nut or bolt can be rotated without distortion of the bearing surface. Flat washers are also used to give tightness to a joint, to prevent leakage, and especially to distribute pressure under the head of a bolt or nut. Dimensional specifications are governed by ASME B18.21.1. USS (United States Standard) flat washers have a larger outer diameter than SAE (Society of Automotive Engineers) flat washers, and can be utilized in nearly any application. ASTM F844 covers the standard specifications for unhardened steel flat washers for general use. Available in zinc plated finish. Zinc plating sacrifices itself, corroding before the base material, offering added corrosion resistance.
If you need more information or want to order washers, please contact us.
Carbon Steel Gasket,Zinc Coated Washers,Galvanized Steel Washers,Galvanized Plate Washers
Taizhou Hongchuang Hardware Co., Ltd. , https://www.jstaizhouhongchuang.com