The gas-shielded arc-shielded arc welding method uses the short-circuit arc-ignition method for arc-ignition. Most of the tungsten-arc argon arc welding adopts the non-contact arc-ignition method, but the short-circuit arc-ignition method is also adopted. The principle of the short-circuit arc-ignition method is described below by taking the gas-shielded gas shielded welding as an example.
When the gas is arc-shielded, the arc is first fed into the arc and gradually approached to the base metal, as shown in Figure 1-2. Once in contact with the base metal, the power supply will provide a large short-circuit current, and the arc is triggered by the wire breaking near point A. If it breaks at point B, the arcing fails. Therefore, the explosion at point A is a necessary condition for successful arc ignition.
The explosion at point A or at point B is mainly due to the magnitude of the resistance heat generated by the wire near the point, that is, the magnitude of the contact resistance. The contact resistance of the two points A and B is shown in Figure 1-3. Point B is the contact point between the welding wire and the contact tip, and the contact resistance R B changes little with time and remains substantially unchanged. At point A, point A is the point of contact between the wire end and the base metal. R A is the contact resistance, and R A is infinite at the moment when the welding wire is in contact with the base material; as the short-circuit current increases, the point A softens rapidly, and the contact area increases, so that R A sharply decreases. It can be seen that in order to ensure the success of the arc ignition, it is desirable that the short-circuit current growth rate di S /dt is as large as possible, and the slower the R A decay rate, the better. That is, when R A is large, the short-circuit current i S is increased to a higher value, so that a burst occurs at point A.
The method to improve the success rate of arc ignition is as follows:
1) Improve the short-circuit current growth rate di S /dt, mainly to improve the working state of the power supply. For example, current transformers often use current inductance to adjust the dynamic characteristics of the welder in order to reduce spatter and improve forming, but reduce di S /dt and reduce arc ignition power. For this reason, the bypass inductor is often used to short-circuit the DC inductor during the arc-triggering, and the inductor is connected after the arc-triggering is successful. Here, when the inverter welder appears, the electronic reactor is fully utilized to adjust the dynamic characteristics of the power supply, and a small DC inductor is selected, so that it is not necessary to adopt the above method, and a very reliable arc-starting process can be obtained.
2) Reduce the decay speed of the contact resistance R A . When the arc is triggered, the wire feed speed is slower, so as to reduce the pressure increase speed of the welding wire and the base metal, and the R A decay speed is slowed down. It is also unfavorable that the wire feeding speed is too slow, and it is usually 1.5 to 3 m/min. After the arc is successfully turned on, it should be converted to the normal wire feeding speed immediately.
3) Use the shear effect to induce arcing. Under normal circumstances, the metal droplets remaining in the end of the wire are cut by pliers during welding to facilitate arc ignition. But this is cumbersome, so many gas shielded welding equipment now have increased ball removal, which is the shearing effect. At the end of the welding, the arc voltage and the wire feed speed are appropriately lowered to realize the automatic ball removing function.
4) When the contact tip wears a large amount, the contact resistance R B at point B will be increased, which is not conducive to arc ignition. To this end, the contact tip should be replaced in time.
surface conditioning disc made of aluminum oxide, are superior in performance, anti-blocking, high abrasion resistant, waterproof, oil-proof and safe.Our Surface Conditioning Discs are torque spiral design with strong flexibility and long service life.Open nylon web (non-woven material) backing leads to better elasticity and plasticity, suitable for different shapes of various objects; and avoids overheating deformation or discoloration.Fine/Medium/Coarse assortment pack can satisfy almost all your general polishing requirements.Come with 1Piece Pad Holder, 1/4" shank fits most power drills, die grinders, air grinders and other Power Tools .We make a full range of abrasive products,we also have drill brush, rubber Sanding Belt cleaning block, Sanding Sponge , Quick Change Disc ,power tools,sanding belt, Plastic Backing Pad ,electric angle grinder, Abrasive Related Products.Usage:Clean weld (point), remove corrosion, rust, patent leather, oxides; remove paint, varnish, sealants, mixture; remove hard ground to the site; quickly remove surface contaminants.This product is suitable for car manufacturers repair industry, construction, chemical light industry, shipbuilding and repairing, machinery manufacturing, furniture manufacturing, decoration industry, public works, as well as self-repair industry.Coarse nylon disc for polishing:Made of woven fabric imbedded in nylon structure of the non woven fibers.Application: Providing additional strength and durability for removing paints,rust, corrosion, exit burrs, weld splatter, parting lines and deburring on ferrous and nonferrous metals.Blending weld seams and deburring edges
We distributes and wholesales various brands of Bonded Abrasives , Abrasive Sanding Disc, Cutting Wheels , Abrasive Flap Disc , Flap Wheels , Flap Disc Backing Pad , Flap Disc Adhesive , and Surface Conditioning Product etc, and enjoy a high position among consumers.
Abrasive Tools Surface Conditioning Product,Brown surface conditioning disc,CRS MED sanding disc,Surface Conditioning Grinding Abrasive Disc,Surface Conditioning Abrasive
Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.abrasive-jd.com