In the synchronous recording and recording, how to ensure the quality of the sound is very important. The following is an analysis brought to you by the Chinese pickup leader Si Zheng Technology.
1: first determine whether the network camera audio input is: LINEIN (linear level)
2: If it is to determine the LINE audio input port, then check whether the microphone power supply is normal, check the connection of the pickup is correct.
If the above two cases are determined, the sound quality recorded by the network camera is still very vague or has no sound?
1: First check, pickup audio signal output connection, the general network camera audio input connector is 3.5 headphone connector, then the corresponding pickup audio signal line, it must be transferred to 3.5 headphone connector.
2: It should be noted that although you plug in a 3.5 headphone connector, but the 3.5 connector, he is divided into two channels and single channel points, that is, stereo and mono, check your 3.5 connector is dual channel or Single channel.
3: If the confirmation is mono, then the positive electrode of the pickup is connected to the positive electrode of 3.5, and the negative electrode is connected to the negative electrode. If you have two channels, then there will be a three-core cable. The negative electrode of the pickup is connected to the negative electrode of 3.5, and the positive electrode is connected to the other two wires corresponding to the 3.5 connector, which are the left and right channels respectively.
4: There is also a situation where the audio input of certain brands of network cameras now has both: LINE and MIC input, that is to say an audio input port, he may be the left channel is the LINE right channel is the MIC, In such a situation, you cannot connect the left and right channels together to connect the positive pole of 3.5. For example, if the negative electrode is connected to the negative electrode, then the positive electrode is connected to one of the 3.5 connectors, and then listen to the sound. If it is not normal, change it to another audio cable. But can't carry on the parallel connection of the left and right channels, also forbid to use the monophonic 3.5 joints, must use the dual-channel joint.
The 3.5 connector is a standard interface in the world. If the 3.5 headphone connector has two black lines, it represents a dual channel interface. The two black lines are actually from the insulating ring. The sharpest part at the top of the 3.5 connector is stereo left. Channel, the middle of the insulation ring is the right channel, and the negative is the ground at the root. If it is a mono 3.5 connector, the opposite is to see only a black insulating ring, the tip is positive, the root to the negative!
Article recommendation:
What is the microphone of monitor head encyclopedia: http://
What is a high-fidelity pickup: http://
1: first determine whether the network camera audio input is: LINEIN (linear level)
2: If it is to determine the LINE audio input port, then check whether the microphone power supply is normal, check the connection of the pickup is correct.
If the above two cases are determined, the sound quality recorded by the network camera is still very vague or has no sound?
1: First check, pickup audio signal output connection, the general network camera audio input connector is 3.5 headphone connector, then the corresponding pickup audio signal line, it must be transferred to 3.5 headphone connector.
2: It should be noted that although you plug in a 3.5 headphone connector, but the 3.5 connector, he is divided into two channels and single channel points, that is, stereo and mono, check your 3.5 connector is dual channel or Single channel.
3: If the confirmation is mono, then the positive electrode of the pickup is connected to the positive electrode of 3.5, and the negative electrode is connected to the negative electrode. If you have two channels, then there will be a three-core cable. The negative electrode of the pickup is connected to the negative electrode of 3.5, and the positive electrode is connected to the other two wires corresponding to the 3.5 connector, which are the left and right channels respectively.
4: There is also a situation where the audio input of certain brands of network cameras now has both: LINE and MIC input, that is to say an audio input port, he may be the left channel is the LINE right channel is the MIC, In such a situation, you cannot connect the left and right channels together to connect the positive pole of 3.5. For example, if the negative electrode is connected to the negative electrode, then the positive electrode is connected to one of the 3.5 connectors, and then listen to the sound. If it is not normal, change it to another audio cable. But can't carry on the parallel connection of the left and right channels, also forbid to use the monophonic 3.5 joints, must use the dual-channel joint.
The 3.5 connector is a standard interface in the world. If the 3.5 headphone connector has two black lines, it represents a dual channel interface. The two black lines are actually from the insulating ring. The sharpest part at the top of the 3.5 connector is stereo left. Channel, the middle of the insulation ring is the right channel, and the negative is the ground at the root. If it is a mono 3.5 connector, the opposite is to see only a black insulating ring, the tip is positive, the root to the negative!
Article recommendation:
What is the microphone of monitor head encyclopedia: http://
What is a high-fidelity pickup: http://
abrasive paper sheet can make to belt ,use for leather and painted surface ,good anti-clogging performance.it is mainyly used for automotive and furniture industry on machinery .can make Velcro Disc and self adhesive disc.the grain surface is under special treated ,for painted surface of furniture and musical instrument.
Abrasive Paper Sheet,Silicon Carbide Paper,Silicon Carbide Emery Paper,Sticky Back Sandpaper Sheet
Henan Yuteng Abrasives Co.,Ltd , https://www.henanyutengabrasives.com