CNC plasma cutting machine for stainless steel cutting processing methods and maintenance knowledge CNC plasma cutting machine for stainless steel "target=_blank> stainless steel cutting processing methods and maintenance knowledge for stainless steel "target=_blank> stainless steel cutting method, Plasma cutting is a thermal processing method. At present, the main cutting method of stainless steel "target=_blank> stainless steel is used in plasma cutting. Now I introduce more stainless steel "target=_blank> stainless steel cutting method:
Because of the special nature of the stainless steel plate, the main processing methods are cold forming and hot working. Cold processing, often slow, and efficient, is mainly used for cutting of specifications and shapes, and the hot processing method is very rich. According to different situations, the cutting effect is not the same, and the cost is also slightly higher and lower!
The stainless steel cutting cold processing methods mainly include: " sawing machine cutting, wire cutting processing water cutting, shearing board cutting, punching processing, drilling processing, etc., the molding quality is generally high, but the efficiency is low, often can not meet the needs of mass production. !
The hot cutting method mainly includes: plasma cutting and laser cutting! These two methods, plasma cutting speed, high efficiency, but the cutting quality is not as good as the laser, but the purchase and use cost of the whole machine is much lower than the laser! Both methods can be applied to the special-shaped cutting requirements of stainless steel "target=_blank> stainless steel plates!
The following is some of our little knowledge about the maintenance of CNC cutting machine.
1. Use a vacuum cleaner to suck dust and dirt from the machine once a week. All electrical cabinets should be kept clean and dustproof.
2, each rail should be cleaned frequently, to eliminate dust and other debris, to ensure that the normal rack of equipment should be wiped regularly, add lubricant, to ensure lubrication and no debris.
3, often check the steel belt, must ensure that the tension.
4. Check the straightness of the track and the verticality of the machine every six months, and find that the maintenance and debugging are not normal.
Second, the gas circuit part of the maintenance
1. Maintenance of gas path system (1) Check the gas path system frequently, and find that the leaking gas and parts that cannot be used normally should be treated in time to ensure the smooth flow of the gas path. (2) Wipe the dust and debris of the airway frequently to prevent premature aging of the airway.
2. The maintenance of the pressure reducing valve adjusts the pressure reducer, and adjusts the pressure gauge to the required pressure. During the adjustment process, the pressure should be reduced from small to large to ensure continuous adjustment of the pressure reducer. If the pressure cannot be continuously adjusted or the gas leaks from the safety valve, a new pressure reducer must be replaced. Fitting the parts of the gas pressure reducer yourself will result in equipment damage and even serious personal injury.
3. Maintenance of torch cutting tempering preventer (1) The cutting torch adopts the machine torch produced by professional manufacturers. The torch is used for a long time, the sealing surface is damaged, and the cutting nozzle is not tightly sealed. It must be repaired with special tools. (2) The torch also adopts the standard fast cutting nozzle produced by professional manufacturers. For the new cutting nozzle, it must be inspected before it can be used. (3) The cutting nozzle is contaminated. It is necessary to clean the preheating flame hole and cut the oxygen channel with special tools.
4. The tempering preventer is an important part to ensure safety. According to the requirements of the safety department, the tempering preventer is strictly prohibited to be dismantled. Therefore, the tempering preventer uses a long-lasting air resistance to ensure that the gas flow rate is not required or leaks, so be sure to replace it with a professional.
Equipment operators must pass professional training before they can be employed. It is strictly forbidden to operate the machine by non-professionals. For more details, please visit the official website of Wuhan Huayucheng http:// http:// http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
180mm (7 Inch) Flat Cut-off Disc
B&H TOOLS CO., LTD. , https://www.bandhtools.com