The precautions are as follows:
ï¬ 1. The general guardrails should be tempered glass or laminated glass. When tempered glass is used, the thickness should not be less than 13mm. Since the glass is a brittle material, the glass must not be in direct contact with the rigid node. There should be elastic material between the two. When the design uses two sides into the glass guardrail, the glass into the pillar slot should have more than 3mm on both sides of the gap, the gap filled with sealant, the glass into the slot not less than 13mm.
ï¬ 2. When glass is used instead of columns in the guardrail, a gap of about 6mm should be left between the glass, and a gap of about 6mm is also left at the intersection of the glass and other materials. The gap is filled with a sealant. The guardrail base is a key part of the fixed guardrail. Generally, angle steel and steel plates are used to form fixed pieces of fixed glass. Both sides of the fixing pieces are fixed firmly with the expansion screw on the floor of the building or by welding and prefabrication. The hardness of the bottom of the glass and fixture is 80- The rubber support blocks of 90 are cushioned, the depth of the glass projecting into the fixture is more than 110mm, and the glass extends into both sides of the fixture (ie, between the angle steel and the steel plate), and a neoprene rubber liner of 3 to 6mm clearance should be left. The glass is clamped. After the installation is inspected and confirmed to be safe and firm without loosening, the surface of the guardrail base is covered with a decorative cover. The gap left between the cover material and the glass is filled with a sealant, and the cover material may not directly contact the glass.
ï¬ 1. The general guardrails should be tempered glass or laminated glass. When tempered glass is used, the thickness should not be less than 13mm. Since the glass is a brittle material, the glass must not be in direct contact with the rigid node. There should be elastic material between the two. When the design uses two sides into the glass guardrail, the glass into the pillar slot should have more than 3mm on both sides of the gap, the gap filled with sealant, the glass into the slot not less than 13mm.
ï¬ 2. When glass is used instead of columns in the guardrail, a gap of about 6mm should be left between the glass, and a gap of about 6mm is also left at the intersection of the glass and other materials. The gap is filled with a sealant. The guardrail base is a key part of the fixed guardrail. Generally, angle steel and steel plates are used to form fixed pieces of fixed glass. Both sides of the fixing pieces are fixed firmly with the expansion screw on the floor of the building or by welding and prefabrication. The hardness of the bottom of the glass and fixture is 80- The rubber support blocks of 90 are cushioned, the depth of the glass projecting into the fixture is more than 110mm, and the glass extends into both sides of the fixture (ie, between the angle steel and the steel plate), and a neoprene rubber liner of 3 to 6mm clearance should be left. The glass is clamped. After the installation is inspected and confirmed to be safe and firm without loosening, the surface of the guardrail base is covered with a decorative cover. The gap left between the cover material and the glass is filled with a sealant, and the cover material may not directly contact the glass.
Stainless steel plate surface smooth, high plasticity, toughness and mechanical strength, acid, alkaline gas, solution and other media corrosion resistance. It is an alloy steel that does not rust easily, but not absolutely. Stainless steel plate refers to the corrosion resistance of weak medium such as atmosphere, steam and water steel plate, and acid resistant steel plate refers to the corrosion resistance of chemical etched medium such as acid, alkali, salt steel plate.
According to the structure is divided into austenitic stainless steel plate, martensitic stainless steel plate (including precipitation hardening stainless steel plate), ferritic stainless steel plate, and austenitic ferritic biphase stainless steel plate and so on four categories? According to the main chemical composition of the steel plate or some characteristic elements in the steel plate to be classified into chromium stainless steel plate, chromium nickel stainless steel plate, chromium nickel molybdenum stainless steel plate and low carbon stainless steel plate, high molybdenum stainless steel plate, high purity stainless steel plate. According to the performance characteristics and use of steel plate classification, is divided into nitric acid resistant stainless steel plate, sulfuric acid resistant stainless steel plate, pitting stainless steel plate, stress corrosion resistant stainless steel plate, high strength stainless steel plate. According to the functional characteristics of the steel plate, it is divided into low temperature stainless steel plate, no magnetic stainless steel plate, easy cutting stainless steel plate, super plastic stainless steel plate. Currently, the commonly used classification method is according to the structural characteristics of steel plate and steel plate chemical composition characteristics and the combination of the two methods. Generally divided into martensitic stainless steel plate, ferritic stainless steel plate, austenitic stainless steel plate, duplex stainless steel plate and precipitation hardening type stainless steel plate or divided into chromium stainless steel plate and nickel stainless steel plate two categories.
Typical uses: pulp and paper equipment heat exchanger, mechanical equipment, dyeing equipment, film washing equipment, pipelines, coastal area building external materials, etc.
304 Stainless Steel Coil,Stainless Steel Mirror Roll,Stainless Steel Plate Coil,Stainless Steel Drawing Plate
Shandong Xinsuju Steel Co.,Ltd. , https://www.sawlpipe.com