What is home improvement baseboard? Baseboards, as the name suggests, are kicked wall areas, so they are more vulnerable to impact. Skirting can better bond the wall and the ground, reduce the deformation of the wall, and avoid damage caused by external forces. In addition to its own function of protecting the walls, the baseboard also occupies a considerable proportion in the proportion of home furnishings. It is the outline of the ground, and sight often falls naturally on it. How to install the baseboard? How can owners self-check?
Second, the home baseboard installation process 
1. Drilling: Before drilling, observe the routing of hydropower to prevent mistakes. Drilling intervals should not be too large, otherwise the baseboard is difficult to stick to the wall. Use a special tool to drill holes in the wall. The length of the home baseboard is 2m. In order to fix the baseboard more firmly, the drilling interval should be about 40cm, and the interval at the interface should be smaller. Stick the small bar into the hole you just made. The nails fixing the baseboard are nailed to the wooden bar and are directly nailed to the wall. The nails are easy to loosen.
2. Fixed: Before fixing the home baseboard, the wall should be leveled and cleaned. Otherwise, after the skirting board is installed, it can't completely adhere to the wall, leaving ugly gaps. Look for the drill hole and fix the nail on the baseboard. When fixing, pay attention to whether the skirting board and the wall are in close contact, and the nail should be completely immersed in the baseboard.
3, corner treatment: Corner, home skirting where the intersection of the baseboard, the edge of the baseboard to cut 45 degrees, so that the interface will not leave unsightly traces. Fix the cut baseboard. Note: The corner baseboard must be cut through a 45-degree angle before it can be spliced ​​and installed, otherwise it will affect the appearance.
Third, home improvement skirting installation considerations1. When the hole is drilled, the pipe of the hydropower project is buried on the wall, and the position of the pipe is just below the switch socket. When drilling, it must be considered a good position to avoid damage.
2, whether it is polymer, MDF, wood material baseboard, have the characteristics of thermal expansion and contraction, so the corner of the baseboard should also be like the floor, leaving about 1cm expansion joints.
3, fixed home skirting nails to use a special screw, such a fixed effect is better, not easy to loose. We must pay attention to whether manufacturers cut corners. The baseboard was originally designed to cover the expansion joints of the floor and make the floor more beautiful. Therefore, the intersection of the skirting boards should be smoothed with a plane. The baseboard must be completely close to the wall without any gaps. It is more beautiful, especially the corners. The flatness of the wall should be tested before installation.
4, in order to obtain better visual effects, the baseboard must be set according to the proportion and functionality, the general baseboard height is 8-12CM high, less than 8CM, the proportion of asymmetry, to create its significance and Visual effects, higher than 12CM, are overly eye-catching and have a feeling of disappointment.
Fourth, home improvement baseboard this step owners need to pay attention to1. The maximum clearance between the home baseboard and the floor should be less than 3mm. Use a coin worth 1 yuan to plug it in. If you plug in more than two, you may have too much clearance.
2, after the home improvement baseboard paving should pay attention to the protection of the foot line, so as not to brush or paint a lot of paint stuck to the surface of the foot line can not clean down.
After reading this article is not a home improvement to have a better understanding of the baseboard, if your home is installing baseboard, I hope to help you. If you want to know more about home decoration, you can pay attention to this site information channel.
Baseboard installation decoration construction knowledge
[7 Working Modes Flashlight]: Headlight (4-6hrs) -High, Medium and Flashing, Side White Lamp (4-7hrs) - High and Medium, Side Red Light (6-7hrs) - Flashing and Slow-flashing; Press the switch to change working mode and long press 3s to change working LED.Its beam can be focused that throws light up to an impressive 700 feet
[Car Emergency Escape Tool]: Features with window breaker break the stuck window and the seat belt cutter to cut the jammed seat belt; bring safe escape in emergencies, having a self defense Led Flashlight tactical can help you get out of most sticky situations
[HANDS-FREE]: With a powerful magnet on the side of the flashlight head, you could attach it to the car or other metallic surface to use as a Work Light, camping lamp or emergency warning light
[Reliable and Necessary]: Flashlight is water resistant & shock resistant for use under the most rugged, emergency condition.It comes with a weather resistant anodized aluminum alloy body, easy to grip, tail with a compass for outdoors; Not just for auto emergencies, also great for working, camping, or hiking as it's designed to withstand lots of abuse
[Rechargeable Emergency Power Bank]: This solar flashlight has a built-in 2000mAh 18650 battery, could be charged with included USB Cable (4-5hrs) or Solar Power (30hrs), using the USB cable to connect your phone with the flashlight (The battery needs to be greater than 20% )and charging your phone for emergency
Solar Powered Flashlight,Solar Powered Torch,Solar Rechargeable Flashlight,Solar Rechargeable Torch
Ningbo Wason Lighting Technology Co.,Ltd , https://www.nbwasonled.com